Felling wedges and breaker bars: what HSE, SafeWork NSW, WorkSafe NZ and WorkSafeBC name
HSE names alloy and plastic wedges, high-lift wedges, a breaking bar, a cant hook and felling cushions. SafeWork NSW, WorkSafe NZ and WorkSafeBC name wedges and wedging tools, with no size or material.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
The text below describes what the named codes and training bodies publish. It is not training and does not teach the work. Five official sources name wedges or breaker bars in felling. Only HSE names a material, a breaking bar or a cant hook.
Tools and types named by each source
| Source | What it names |
|---|---|
| HSE, Chainsaws at work, INDG317 (rev2, January 2013) | Aid tools for felling: alloy or plastic wedges, a breaking bar, a cant hook, a winch, or high-lift wedges and a sledgehammer. Its figure of aid tools shows a breaker bar with a cant hook, a log pick, pulp hooks, high-lift wedges and log tongs. Felling cushions are named as an alternative to wedges |
| HSE, Working with chainsaws web page | Felling aids like breaker bars and wedges must be appropriate to the tree size and form. The need for them is to be identified in advance, and they are to be appropriate and readily available to the person making the fell |
| SafeWork NSW, Tree works code of practice, March 2026, chapter 9 | Suitable equipment such as wedges should be considered to prevent a tree falling in a direction other than the one intended. For clear felling, wedges are used as needed to assist the fall direction. For controlled directional felling, wedges may be used to assist |
| WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, section 3.4.1 | Where the size of the tree has the potential to cause harm, wedges, block and tackle, rope, wire cable or other appropriate devices are used. Wedges and driving tools should be readily available during all felling operations |
| WorkSafeBC, OHS Regulation Part 26, sections 26.24 and 26.26 | Wedging tools must be immediately available. Unless the tree has a pronounced favourable lean, wedges must be set. Where one tree is used to bring down a partially cut tree, a wedge is driven into the backcut of each partially cut tree |
Types
HSE separates two kinds of device. Wedges are named as alloy or plastic, with high-lift wedges as a type that applies forces well in excess of those from a breaking bar. In HSE's words they give operators more control and spare their backs. The second kind is the lever: the breaking bar and the cant hook, drawn together as a breaker bar with a cant hook. Felling cushions are inflated with exhaust gas from the chainsaw and force the tree over, as an alternative to wedges.
The other three regulators use the single word wedges, plus WorkSafe NZ's driving tools and WorkSafeBC's wedging tools. None prints a size, a material, a weight or a maker. SafeWork NSW lists wedges in its felling chapter beside ropes and winches for controlled directional felling, and WorkSafe NZ lists them with block and tackle, rope and wire cable.
Limits placed on wedging
WorkSafeBC adds limits for dangerous trees. The undercut is made as deep as necessary to minimise the use of wedges and the vibration that comes with them. Wedging over is used only if there is no alternative, and after a careful assessment of the ability of the dangerous tree to withstand wedging.
WorkSafeBC's wording is regulation and uses "must". SafeWork NSW's code uses "should" and "may", and the WorkSafe NZ approved code uses both "shall" and "should". HSE's leaflet is guidance. Moving timber with the same aids is covered in the guide to log handling aid tools, and the cuts the wedges work with in the guide to notch, hinge and back cut names.
Sources
- HSE, Chainsaws at work, INDG317 (rev2), published January 2013, read October 21, 2026
- HSE, Working with chainsaws (tree work, safety topics), read October 21, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 21, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 21, 2026
- WorkSafeBC, OHS Regulation Part 26 Forestry Operations, read October 21, 2026