ArbNation Join free

Flail and boom mowers: HSE guidance and a maker's manual for hedge cutters

HSE publishes an information sheet, a risk assessment example and an impact hazards page for tractor-mounted flail hedge cutters. A maker's manual for a 1.2 m flail head lists its own warnings.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

The named regulator and maker are described here as published. It is not training and does not teach the work. Three Health and Safety Executive pages cover tractor-mounted flail hedge cutters, and one maker's manual covers a 1.2 m flail head.

The HSE information sheet

HSE information sheet AIS21 (rev1), Safe use of rotary flail hedge cutters, dates from 2012. It describes the hazards of tractor-mounted rotary flail hedge cutters and gives guidance on lowering the risk to the operator and to others. It is written for employers, employees and the self-employed. The revision covers guards, machine safety and safe working practices. It has minor updates, and HSE states that the guidance remains the same.

The HSE risk assessment example

HSE also prints a basic risk assessment example for a tractor-mounted flail hedge cutter. It is a guide for the steps a manufacturer or designer takes to evaluate a machine before it is built. Selected entries follow.

Hazards and measures in the HSE example
Hazard and sourceMeasure listed
Entanglement in drive shafts, including the PTOShaft guards and a stand-off guard for the head, to the relevant BS or CEN standard
Ejection of flailsA head cowl that directs ejected flails away from the tractor, a breakaway head, freely rotating flails, and a design that stops the head touching the ground
Stabbing by ejected debrisA head shaped to direct debris away from the tractor, and guards for the cab
Unexpected start-up when the tractor startsControl levers that return to neutral on release or when power is disengaged
Loss of stability with the arm at maximum reachWeight distribution and a recommended tractor ballast weight range
Unexpected arm movement in transportIsolators for the hydraulic controls and locking pins that hold the arm in the transport position
High pressure fluid injection from the hydraulicsManufacture to the relevant standard, hose routes that avoid chafing, and pressure relief valves
Electric shock from overhead power linesWarning signs on the machine and in the manual, with machine height and reach

The example also lists crushing and shearing at the arm, break-up of the head, control failure and overrun, noise and vibration, errors in fitting, control position and falls from the machine during maintenance.

The HSE impact hazards page

HSE's impact hazards page groups hedge cutters, mowers and tree harvesters as machines that eject flails, blades and chain shot. It lists operator error as entering the danger zone, failing to fit or maintain blades and flails, and failing to fit or maintain protection against ejected material.

The design points are fixed guards, trip bars where guarding is not practical, and deflectors or skirts strong enough to stop stones, wire and other objects reaching the operator and bystanders. For machines that cannot be guarded, HSE says additional operator protection might include mesh guards or impact resistant glazing on cabs and specified safe working zones. Instructions for these machines are to cover settings, safe working zones, replacement parts, safety device tests and any added operator protection.

A maker's manual for a 1.2 m flail head

The manual is edition 1.0 of October 2012. It carries an EC declaration of conformity under Machinery Directive 2006/42/EC. Its warning stickers cover fluid escaping under pressure, flying objects and staying clear of the flails. Others cover shutting off the engine and removing the key before maintenance, overhead power lines, reading the manual, checking nuts every 8 hours and not removing the guard.

The manual lists these potential dangers: becoming trapped when hitching, tractor overbalancing with the arm extended, electrocution on overhead lines, the PTO, moving parts, flying debris, machine overbalancing, oil injection and collisions with other machines or road debris. It gives a PTO speed limit of 540 rpm. On power lines, the manual puts the minimum legal height for 11,000 and 22,000-volt cables at 5.2 metres. A fully extended machine may exceed it.

For other tractor-mounted and handheld hedge tools, see the guide to hedge trimmer safety.

Sources