ArbNation Join free

CE and UKCA marks on a harness or lanyard: what the regulations and makers print

Falling from a height is a risk category III risk. The GB version of Regulation 2016/425 puts the approved body's number after the mark, and gov.uk sets the mark at least 5 mm high.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here.

Where harnesses and lanyards sit

Regulation (EU) 2016/425 on personal protective equipment, as it applies in Great Britain on legislation.gov.uk, sorts PPE into three risk categories in Annex I. Category III lists risks that may cause very serious consequences such as death or irreversible damage to health.

Falling from a height is on that list, along with electric shock and live working and cuts by hand-held chainsaws.

Marking rules in the Regulation

ProvisionWording
Article 16The marking is subject to the general principles in Article 30 of Regulation (EC) No 765/2008.
Article 17(1)The marking is affixed visibly, legibly and indelibly to the PPE. Where that is not possible or not warranted by the nature of the PPE, it goes on the packaging and the accompanying documents.
Article 17(2)The marking is affixed before the PPE is placed on the market.
Article 17(3)For category III PPE the marking is followed by the identification number of the approved body involved in the procedure in Annex VII or VIII. The body affixes its own number, or the manufacturer or authorised representative does so under its instructions.
Article 17(4)The marking and the body number may be followed by a pictogram or other marking showing the risk the PPE protects against.
Article 8(5)The PPE carries a type, batch or serial number or other element allowing its identification, or the manufacturer gives it on the packaging or in a document where size or nature does not allow.
Article 8(6)The manufacturer indicates its name, registered trade name or trade mark and a single postal address on the PPE, or where that is not possible on the packaging or in a document.

The text on legislation.gov.uk reads "UK marking" and "approved body". The original EU text reads "CE marking" and "notified body". Article 17(1A) lets the UK marking sit on a label or accompanying document for seven years from IP completion day.

What gov.uk prints on UKCA and CE marks

The Department for Business and Trade guidance "Placing UKCA or CE marked products on the market in Great Britain" was published March 31, 2026 and last updated August 21, 2026. It records that Great Britain continues to recognise the CE marking alongside or in place of the UKCA marking under the Product Safety and Metrology (Amendment) Regulations 2024.

  • A product can carry several markings, UKCA and CE among them, as long as the markings can be seen.
  • Markings are in their standard form, scaled in proportion, at least 5 mm high unless the product rules set another minimum, and easily visible, legible and indelible.
  • Manufacturers and importers indicate their name, registered trade name or trade mark, and postal address.
  • Other indications may include type identification, batch number, serial number, model and CAB number.
  • Legislation in force lets the UKCA marking sit on a label or accompanying document until 11pm on 31 December 2027.
  • The CE marking goes on the product or its data plate, and on the packaging and documents where that is not possible.

Offences and penalties

The Personal Protective Equipment (Enforcement) Regulations 2018 (SI 2018/390) came into force on April 21, 2018. Regulation 7 makes it an offence for an economic operator to contravene Articles 8, 10, 11, 13, 16 and 17.

The England, Wales and Scotland version names the UK marking in that list. The Northern Ireland version names the CE marking. Regulation 8 sets, on summary conviction, a fine or imprisonment for up to three months, or both, in England and Wales. In Scotland and Northern Ireland it sets a fine not exceeding level 5 on the standard scale or imprisonment for up to three months, or both.

Numbers and dates makers print

Makers publish their own legends. One maker's markings page gives CE0598 as an example, where the number 0598 identifies the notified body responsible for the PPE conformity assessment and production surveillance.

Its serial runs as year, day of the year, a four-digit number and a machine letter. Another maker's technical notice for a rope ascender lists the notified body for the type examination, the notified body for production control, the serial number, year and month of manufacture and a Data Matrix.

Layouts differ by maker. Other pages here cover markings on new climbing gear, the standard numbers on tree gear and Regulation 2016/425 and the UK PPE rules.

Sources