ArbNation Join free

Crane load charts: rated capacity, radius and derating in OSHA and HSE texts

OSHA defines rated capacity as the maker's maximum working load under stated conditions, radii included. HSE's lifting-equipment code defines derating as cutting a marked safe working load to suit where and how the equipment is used.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work. The US text is 29 CFR 1926.1401, the definitions section, and 1926.1417, the operation section. The UK texts are the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) and the HSE Approved Code of Practice L113.

Rated capacity in the OSHA definitions

Section 1926.1401 defines rated capacity as the maximum working load the manufacturer permits under specified working conditions. Those conditions usually include a specific combination of factors such as equipment configuration, radii, boom length and other parameters of use.

The same section defines two devices by radius. A load moment indicator senses the overturning moment, which it describes as load multiplied by radius. It compares that with the rated capacity and shows the percentage of capacity in use. A load moment limiter makes the same comparison. When rated capacity is reached it cuts power to functions that raise the loading, such as hoisting, telescoping out or luffing out.

Load charts in 29 CFR 1926.1417

Section 1926.1417 lists the rated capacities, called load charts, among the operating procedures that must be readily available in the cab at all times. If the capacities exist in the cab only in electronic form and that fails, the operator must cease operations or follow safe shut-down procedures until they are available again.

The section states that equipment must not be operated in excess of its rated capacity, and that an operator must not be required to do so. It allows two ways to check a load against rated capacity.

  • Take the weight from an industry-recognised source or calculation method, or from other equally reliable means.
  • Begin hoisting and use a load weighing device, load moment indicator, rated capacity indicator or limiter to see whether the load exceeds 75 percent of maximum rated capacity at the longest radius used in the lift. If it does, the lift does not proceed until the weight is confirmed by the first method.

Other paragraphs touch capacity. A competent person adjusts the equipment or operations for the effect of wind, ice and snow on stability and rated capacity. When a load is travelled, a competent person decides whether rated capacity needs reducing. Safety devices and operational aids must not substitute for the operator's professional judgment. Where the manufacturer's capacity procedures are unavailable, a registered professional engineer familiar with the equipment must develop and sign them.

Safe working load in LOLER and HSE L113

Regulation 7 of LOLER requires lifting machinery to carry a clear marking of its safe working load. Where the load depends on configuration, the machinery is marked for each configuration, or information giving it is kept with the machinery.

HSE L113 defines a safe working load (SWL) as a value or set of values based on the strength or stability of the equipment when lifting. It adds that the phrase rated capacity is sometimes used for the same thing. The code names lifting machinery whose SWL changes with operating radius.

  • Any crane with a jib that can be raised or lowered.
  • A mobile crane or forklift truck with a telescopic jib.
  • A MEWP on a cantilevered arm.

For those machines the code calls for clear marking or adequate information on the matching SWL, in the form of an indicator, plate, chart or certificate that the operator can reach. The code wants hard copies in a durable format, such as laminated. Where there is a significant hazard, the code points to rated capacity indicators and rated capacity limiters. It says rated capacity indicators were previously known as automatic safe load indicators or moment load indicators.

Derating and overload in HSE L113

L113 describes derating as reducing a marked SWL to account for where and how the equipment is used. Its examples include a carpet boom fitted to a forklift truck and the leg angle of a sling. For a crane working from a floating vessel, the extent of derating is set by a competent person from the manufacturer's recommendations, and the code refers readers to BS 7121 for further guidance.

The code says a load greater than the SWL or rated capacity should not be lifted, except where a competent person requires it for thorough examination or testing.

Terms side by side

TermOSHA, 29 CFR 1926.1401 and 1926.1417HSE L113 and LOLER
Rated capacity or safe working loadDefined in 1926.1401 as the maker's maximum working load under specified conditionsSWL defined by strength or stability; rated capacity named as another phrase for it
RadiusNo separate definition in 1926.1401. It appears inside the definitions of rated capacity and the load moment devices, and as "longest radius" in 1926.1417No separate definition. The code says SWL can vary with operating radius and lists the machines where it does
DeratingNo separate definition in 1926.1401. Section 1926.1417 refers to reducing rated capacity for travelling with a load and for wind, ice and snowDefined in L113 as reducing a marked SWL for where and how the equipment is used

Sources